FDA Status | Packaging

DESCRIPTION

        ASI 335 Neutral Cure Silicone Sealant/Adhesive is a one-part, non-slump, moisture-curing RTV (room temperature vulcanizing) that cures to form a tough, high modulus rubber with long-term flexibility and durability. The neutral curing mechanism of ASI 335 is ideally suited for use in confined work areas since no objectionable odors are evolved. The non-slump characteristics of ASI 335 allow application to vertical or horizontal joints without flowing or sagging. ASI 335 has excellent resistance to weathering including ozone, ultraviolet radiation, freeze-thaw conditions and airborne chemicals. After cure, the wide heat stability range of ASI 335 is from -57°C to +204°C (-70°F to 400°F) and the sealant can be applied to surface temperatures from -18°C to +50°C (0°F to +120°F).
 
 

TYPICAL USES

        ASI 335 can be used as a durable, general-purpose sealant/adhesive in a wide range of industrial applications. Unprimed adhesion to a wide range of substrates is available with the use of ASI 335. For example, ASI 335 adheres to unprimed chrome and stainless steel, which other high modulus silicone sealants would require to be primed. ASI 335 Neutral-Cure Silicone Sealant/Adhesive. As a formed-in-place gasket, ASI 335 exhibits low swell, low compression set and good oil resistance. These characteristics impart an unusual balance of properties to ASI 335 to prevent leakage in harsh environments such as engines, transmissions, water pumps, rear axles and oil pans. ASI 335 is not recommended to be used in cylinder heads, exhaust manifolds or in contact with fuels.
 
 

DIRECTIONS

        ASI 335 is ready to use and requires no mixing or additives. The cure mechanism begins as soon as the sealant comes in contact with the air. At conditions of 25°C (77°F) and 50% relative humidity, the sealant will skin in 10-20 minutes and cure in 24 hours (1/8" bead), with full cure strength in 7 days. Higher humidity accelerates cure. Tooling should be done before skinning takes place. In applications where partial or total confinement of sealant is prevalent, the time required for proper cure is generally lengthened by the degree of confinement.
 
 

SURFACE PREPARATION

        Provided that all bonding surfaces are clean and dry, ASI 335 has excellent unprimed adhesion to most substrates. If there is any doubt about contamination, surfaces should be solvent wiped with oil-free solvents, such as xylol, toluol, naphtha or non-flammable chlorinated solvents. Do not solvent-wipe with oil-based solvents such as Varsol.
 
 

PRIMING

        Priming for ASI 335 is normally not required for application to most substrates. Unprimed adhesion can be readily tested by applying a small trial bead and allowing 7 days for maximum adhesion to occur. ASI 335 has excellent unprimed adhesion to many substrates as shown in the adhesion chart.
 
 

PAINTING

        ASI 335 should not be applied to surfaces that will be painted. Painting over sealant is not recommended because paint film does not stretch with the extension of the sealant and the adhesion of paint to the sealant is not adequate.
 
 

COLORS

        ASI 335 is available in clear, white and black. Special colors are available upon request. Call for price and availability.
 
 

MILITARY SPECIFICATIONS

        ASI 335 meets the requirements of MIL-A-46146A, Type 1.
 
 

FDA STATUS

        When fully cured, ASI 335 is permitted under regulations of the Food and Drug Administration where incidental food contact might be involved. FDA Regulation number is 175.105.
 
 

PACKAGING

        ASI 335 is supplied in (10.2 fl. oz.) caulking cartridge; (40 lb.) pail and (440 lb.) drum.
  theme-->

Click here for Full Technical Information